Vielen dank für die hilfe
Fredrik (Schweden)
Die Suche ergab 16 Treffer
- 27.01.2024, 17:51
- Forum: Schrauben im Normalbereich
- Thema: Dichtung türdrehfenster
- Antworten: 14
- Zugriffe: 1555
- 20.01.2024, 20:03
- Forum: Schrauben im Normalbereich
- Thema: Dichtung türdrehfenster
- Antworten: 14
- Zugriffe: 1555
Dichtung türdrehfenster
Hallo , ich habe bei OTR neue Gummidichtungen für die zu öffnenden kleinen Frontfenster (türdrehfenster) gefunden . https://www.o-t-r.de/shop/rekord-c-commodore-a/tuerdrehfensterdichtung-rechts-und-links-rekord-c-commodore-a/ Wo finde ich die andere Dichtung an meinem Finger im beigefügten Bild? Dan...
- 29.05.2023, 14:08
- Forum: Schrauben im Normalbereich
- Thema: Kleber haube
- Antworten: 3
- Zugriffe: 628
Kleber haube
Hi, I am renovating the hood on the car, removing rust and painting. where should the reinforcement "cross" underneath the hood be glued to, around all edges or special places? I Will use Sicaflex 221, strong bit slightly flexibel. I know people have tried to weld resulting in a cracked ho...
- 23.02.2023, 09:26
- Forum: Schrauben im Normalbereich
- Thema: Heizungsventil
- Antworten: 23
- Zugriffe: 1470
Re: Heizungsventil
Super, danke für die schnellen und ausführlichen Antworten.
Excellent, thanks for fast and detailed replies.
/Fredrik
Excellent, thanks for fast and detailed replies.
/Fredrik
- 22.02.2023, 22:14
- Forum: Schrauben im Normalbereich
- Thema: Heizungsventil
- Antworten: 23
- Zugriffe: 1470
Re: Heizungsventil
Hallo, Danke! Ich muss zugeben, dass ich immer noch nicht verstehe, wie ”BIS” funktionieren könnte; Ein Schlauch vom "Heizelement" sollte zur Wasserpumpe und der andere Schlauch zum Thermostatgehäuse gehen. Das Heizungsregulierventil soll in Reihe mit dem Thermostatschlauch angeschlossen w...
- 22.02.2023, 20:20
- Forum: Schrauben im Normalbereich
- Thema: Heizungsventil
- Antworten: 23
- Zugriffe: 1470
Heizungsventil
Hallo, Ich musste mein Heizungsventil ersetzen. Ich habe gekauft, was als Original für Opel Rekord C/Commodore A angegeben war, aber wenn ich jetzt genauer hinschaue, macht die Platzierung von Ein- und Ausgängen keinen Sinn. Ich habe jetzt im Netz gesucht und gesehen, dass auch eine andere Version v...
- 10.01.2023, 19:26
- Forum: Vorstellungen
- Thema: Radlager hinten
- Antworten: 37
- Zugriffe: 8117
Re: Radlager hinten
Hi again, So I tried one final time to press the bearing all the way. Dis not work, the conical parts on the Axel is bigger than on the bearing. Looking at the inner part of the old bearing it is obvious that the conical part is much bigger than on the new ones. I can not find any other supplier of ...
- 10.01.2023, 14:07
- Forum: Vorstellungen
- Thema: Radlager hinten
- Antworten: 37
- Zugriffe: 8117
Re: Radlager hinten
The new bearing is sitting really tight but I would prefer to have it all the way in, not leaving 1-2 mm.
- 10.01.2023, 14:05
- Forum: Vorstellungen
- Thema: Radlager hinten
- Antworten: 37
- Zugriffe: 8117
Re: Radlager hinten
No, I wait until I feel confident that the bearing is ok until I put the retaining ring on.
/Fredrik
/Fredrik
- 10.01.2023, 13:50
- Forum: Vorstellungen
- Thema: Radlager hinten
- Antworten: 37
- Zugriffe: 8117
Re: Radlager hinten
Hi, The old bearing did not go off easily, I used an angle grinder. You can see there is some conical form in the bearing in my first post with images. Unfortunately no good image of the axle. Hi, Das alte Lager ging nicht leicht ab, ich benutzte einen Winkelschleifer. Sie können sehen, dass das Lag...
- 10.01.2023, 13:00
- Forum: Vorstellungen
- Thema: Radlager hinten
- Antworten: 37
- Zugriffe: 8117
Re: Radlager hinten
Hi, I must admit I did not use heat/cold to facilitate the assembly of the bearing. For the ”shrink ring” I was planning to heat the ring and put the axle in the freezer. If I knew the bearings where 100% correct for my car then it would be easier but I start having doubts and think something will b...
- 09.01.2023, 16:16
- Forum: Vorstellungen
- Thema: Radlager hinten
- Antworten: 37
- Zugriffe: 8117
Re: Radlager hinten
Hi again, Close to assemble everything with new parts again. Using 0.8 mm distance/spacers will give +0.1 mm press on the bearing. However I can not press the bearing all the way in against the axle edge. Is it ok with 1-2 mm gap? I know the last 2 mm of the axle is cone shaped. Hallo, Nah alles mit...
- 22.12.2022, 07:08
- Forum: Vorstellungen
- Thema: Radlager hinten
- Antworten: 37
- Zugriffe: 8117
Re: Radlager hinten
Hi all,
Got this answer from PS autoteile;
”es gab beidere lagerversionen von Opel. Der metallring muss nach aussen stehen.”
Sorry my German is not that good, to which side should the protruding metallring face, inwards to the center of the car or outwards towards the brakes?
/Fredrik
Got this answer from PS autoteile;
”es gab beidere lagerversionen von Opel. Der metallring muss nach aussen stehen.”
Sorry my German is not that good, to which side should the protruding metallring face, inwards to the center of the car or outwards towards the brakes?
/Fredrik
- 21.12.2022, 16:28
- Forum: Vorstellungen
- Thema: Radlager hinten
- Antworten: 37
- Zugriffe: 8117
Re: Radlager hinten
Excellent, thanks for the repair manual picture Joan! Still not sure in which direction I should install the bearing though. I send an e-mail to the supplier PS autoteile but I guess the do not have that detailed knowledge. I also send an e-mail to Krausse Rennsport and asked how the bearings they s...
- 20.12.2022, 21:59
- Forum: Vorstellungen
- Thema: Radlager hinten
- Antworten: 37
- Zugriffe: 8117
Re: Radlager hinten
Hi, Thanks for the input. Should I use any Loctite or similar to fix the bearing in the ”house”? When I removed the old bearings/rear axle it was quite easy, I guess the bearing does not have to be supertight/hard pressed in the ”house” since you also have some pressure sideways on the outer part of...